LVTHA Datasheet, LVTHA PDF, LVTHA Data sheet, LVTHA manual, LVTHA pdf, LVTHA, datenblatt, Electronics. LVTHA datasheet, LVTHA circuit, LVTHA data sheet: TI – V ABT BIT BUS TRANSCEIVERS WITH 3-STATE OUTPUTS,alldatasheet. LVTHA Datasheet: V ABT BIT BUS TRANSCEIVERS WITH 3- STATE OUTPUTS, LVTHA PDF Download Texas Instruments, LVTHA.
|Published (Last):||12 November 2006|
|PDF File Size:||6.46 Mb|
|ePub File Size:||16.71 Mb|
|Price:||Free* [*Free Regsitration Required]|
The devices are designed for asynchronous communication between two data buses. The logic levels of the direction-control DIR input and the output-enable OE input activate either the B-port outputs or the A-port outputs or place both output ports into the high-impedance mode. The datasheft transmits data from the A bus to the B bus when the B-port outputs lvth1625a activated, and from the B bus to the A bus when the A-port outputs are activated.
Active bus-hold circuitry holds unused or undriven inputs at a valid logic state. Use of pullup or pulldown resistors with the bus-hold circuitry is not recommended. When VCC is between 0 and 1. However, to ensure the high-impedance state above 1. These devices are fully specified for hot-insertion applications using Ioff and power-up 3-state. The Ioff circuitry disables the outputs, preventing damaging current backflow through the devices when they are powered down.
The power-up 3-state circuitry places the outputs in the high-impedance state during power up and power lvth16245, which prevents driver conflict.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. lvth162455a
Widebus is a trademark of Texas Instruments. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. On all other products, production processing does not necessarily include testing of all parameters. These are stress ratings only, and functional lvth166245a of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied.
Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed.
The package thermal impedance is calculated in accordance with JESD It is the minimum overdrive current required to switch the input from one state to another. CL includes probe and jig capacitance. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control. Waveform 2 is for an datxsheet with internal conditions such that the output is high, except when disabled by the output control.
All input pulses are supplied by generators having the following characteristics: The outputs are measured datashee at a time, with one transition per measurement. Product device recommended for new designs.
TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. Device has been announced but is not in production.
Samples may or may not be available. TI has discontinued the production of the device. TI’s terms datsheet or “Pb-Free” mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.
Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. This component has a RoHS exemption for either 1 lead-based flip-chip solder bumps used between the die and package, or 2 lead-based die adhesive used between the die and leadframe.
LVTHA (TI) PDF技术资料下载 LVTHA 供应信息 IC Datasheet 数据表 (1/18 页)
If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. Finish options are separated by a vertical ruled line.
Important Information and Disclaimer: The information provided on this page represents TI’s knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information.
Data Sheet Catalog: Begin marking SMD with L
Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and datasbeet information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may datazheet be available for release.
All linear dimensions are in inches millimeters. This drawing is subject to change without notice. This package can be hermetically sealed with a ceramic lid using glass frit.
All linear dimensions are in millimeters. Body dimensions do not include mold flash or protrusion, not to exceed 0,15 per side. Body dimensions do not include mold protrusion not to exceed 0, Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. Buyers are responsible for their products and applications using TI lvth16425a.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices.
TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and xatasheet implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be datasgeet by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions.
Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. Nonetheless, such components are subject to these terms.
No TI lvtn16245a are authorized for use in FDA Class III or similar life-critical medical equipment unless authorized officers of the parties have executed a special agreement specifically governing such use. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer’s risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use.
Products Applications Audio www. It’s a community-based project which helps to repair anything.