LG LCWSLA1 datasheet, Display Module (1-page), LCWSLA1 datasheet, LCWSLA1 pdf, LCWSLA1 datasheet pdf. LG Philips ” LCD Panel for TV，Increase brightness，Add touch，Total solution kits，Customized display，Connector，LCWSLA1,LG Philips,Wide . LCWSLA1 – Download as PDF File .pdf), Text File .txt) or read online. panel datasheet.
|Published (Last):||13 August 2008|
|PDF File Size:||11.89 Mb|
|ePub File Size:||17.14 Mb|
|Price:||Free* [*Free Regsitration Required]|
Search the history of over billion web pages on the Internet. Full text of ” Datasheet: Datasheet, inventory and accessory! The matrix employs a-Si Thin Film Transistor as the active element. It is a transmissive type display operating in the normally black mode. It has a Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arranged in vertical stripes.
Gray scale or the luminance of the sub-pixel color is determined with a 8-bit gray scale signal for each dot, thus presenting a palette of more than It has been designed to apply the 8-bit 1-port LVDS interface. General Features Active Screen Size Pixel Pitch 1 Absolute Maximum Ratings The following items are maximum values which, if exceeded, may cause faulty operation or damage to the LCD module.
Temperature and relative humidity range are shown in the figure below. Electrical Characteristics It requires two power inputs. One is employed to power for the LCD circuit.
Power Input Voltage Vlcd The current is specified at the maximum current pattern. The duration of rush current is about 2ms and rising time of power input is 1ms min. Lx320w01 Mosaic Lc320q01 8 x 6 Ver. Unit Not e Inverter: Input Voltage Vbl The soa1 current and power consumption are wla1 the typical supply Input voltage, This Vbr-B Voltage control brightness.
Vbr-B Voltage Function 3. Specified values are for a single lamp which is aligned horizontally. Interface Connections This LCD module employs two kinds of interface connection, a pin connector is used for the module electronics and one pin connectors are used for the integral backlight system.
If the pin no. See page 9 and When 10 pin is no connection, DCR is disabled. LCD operate itself some test patterns. LCD operate itself a black pattern. All Vlcd power input pins should be connected together. DS90C or Compatible 3. Backlight Inverter The inverter connector is WRB1 side entry type manufactured by YeonHo or equivalent The pin configuration for the 14 pin connector is shown in the table below. Connector 1 Connector Receptacle: If you use spread spectrum for EMI, add some additional clock to minimum value for clock margin.
The performance of the electro-optical characteristics may be influenced by variance of the vertical refresh rate and the horizontal frequency. Timing should be set based on clock frequency. Color Data Reference The brightness of each primary coloured, green, blue is based on the 8-bit gray scale data input for the color the higher the binary input, the brighter the color.
The below table provides a reference for color versus data input. Please avoid the floating state of interface signal at invalid period. There is no reliability problem. T1 describes rising time of 0V to 24V and is not applied at restarting time. When V BL 24V is supplied always, there is no reliability problem. T3 max is less than T2.
For 1 second after lamp on, V br -B should be max level 3. Contrast Ratio CR is defined mathematically as: Surface Luminance L WH is the luminance value at center 1 -point across the LCD surface 50cm from the surface with all pixels displaying white.
For more information see the FIG. For more information, see the FIG. Oc320w01 additional information see the FIG. Viewing angle lc320w10 the angle at which the contrast ratio is greater than ld320w01 The angles are determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the LCD module surface. Gray scale specification Gamma Value is approximately 2. For more information, see the Table Mechanical Characteristics The following items provide general mechanical characteristics.
In addition, the figures in the next page show the detail information of mechanical drawing for LCD module.
Please refer to a mechanic drawing in terms of tolerance at the next page. It should be recommended that any exterior materials do not go passing up the red area slanted. For example, electrical cable, system boardetc. Otherwise, it could cause that abnormal display happens. The label is attached to the backside of the LCD module.
This is subject to change without prior notice. Packing Form a Package quantity in one box: Mounting Precautions 1 You must mount a module using holes arranged in four corners or four sides.
Twisted stress is not applied to the module. And the case on which a module is mounted should have sufficient strength so that external force is not transmitted directly to the module. Transparent protective plate should have sufficient strength in order to the resist external force. And please do not rub with dust clothes with chemical treatment.
Do not touch the surface of polarizer for bare hand or greasy cloth.
Some cosmetics are detrimental to the polarizer. Do not use acetone, toluene and alcohol because they cause chemical damage to the polarizer. Their long time contact with polarizer causes deformations and color fading.
T-CON BOARD 6870C-0142B(2L) LC320W01-SLA1
Operating Precautions 1 The spike noise causes the mis-operation of circuits. It should be lower than following voltage: In lower temperature, it becomes longer. In lower temperature, it becomes lower. And in lower temperature, response time required time that brightness is stable after turned on becomes longer. Condensation makes damage to polarizer or lv320w01 contacted parts. And after fading condensation, smear or spot will occur. Sufficient suppression to the lc320w001 interference sl1a be done by system manufacturers.
Grounding and shielding methods may be important to minimized the interference. Electrostatic Discharge Control Since a module is composed of electronic circuits, it is not strong to electrostatic discharge.
Make certain that treatment persons are connected to ground through wrist band etc. Precautions for Strong Light Exposure Strong light exposure causes degradation of polarizer and color filter. Storage When storing modules as spares for a long time, the following precautions are necessary.
【Lcwsla1】HKinventory – На складе поставщиков в году【цена】【Datasheet PDF】
Do not expose the module to sunlight or fluorescent light. It is recommended that they be stored in the container in which they were shipped. Handling Precautions for Protection Film 1 The protection film is attached to the bezel with a small masking tape. When the protection film is peeled off, static electricity is generated between the film and polarizer. This should be peeled off slowly and carefully by people who are electrically grounded and with well ion- blown equipment or in such a condition, etc.
When the glue remains on the bezel surface or its vestige is recognized, please wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal- hexane. L x W x H Pallet gross weight: M Ass’y Factory code Ver.