Eheim – Professional II Canister Filters. Comment. I have been operating two ‘s for six years and one for the past four years and love how simple the . Eheim Double Tap Unit Sealing Ring Set for /// – 2 pk ( ). Quantity. USD Eheim Pro II Canister Filter Parts, Eheim Double. LTWHOME Replacement Blue Coarse and White Fine Filter Pads Sets Fit for Eheim Professional Pro 2 // / and Experience
|Published (Last):||12 January 2004|
|PDF File Size:||1.57 Mb|
|ePub File Size:||15.74 Mb|
|Price:||Free* [*Free Regsitration Required]|
Results 1 to 11 of Eheim pro II problems. Ok so i hooked my new Eheim up and well everything is going smoothly for the first hour, primed it and such. It was making a bit more noise than I thought it should but figured it was just working the air out. However, after an hour or so its making a ton of noise.
I go to check it out and in doing so it just shuts off. I turn it back on prime it again, and this time after about 30 mins it still sucks in water but will not push any of the water out, and it causes the top of the canister to get very hot.
I have no idea whats going on. I tried to re-lube the canister o-ring thing they tell you to do in the manuel.
THis worked for a little but then it just stopped pushing air or water out. Eheim pro II problems Are you sure it is primed properly. So if it’s not doing that, I suspect it’s not primed properly. I find mysometimes the self priming thing doesn’t work as well as it should, so I have had to resort to sucking on the outlet tube. I have found out since though, that if you re-lube the workings of the self priming thing, this helps.
For a filter to be primed, the cannister must be full of water and both hoses should also be full. Is this the profesjonal with yours?
Eheim pro II problems no not the case as of right now.
Eheim pro II problems
But it has to be a primeing problem. The thing i dont get is both tubes and canister will b filled. Then outta no where the outlet will drain out and it will just stop. Eheim pro II problems Mine will not work unless both hoses are filled. I believe that’s ehem of the priming process. That has sometimes helped kick start mine.
EHEIM Professional II Canister Filter 2026
If all these don’t work, then I am stumped. Hope you get it started. I hope you have some other eheim experts pop in, as these are the only things I’ve needed to try so far.
When you’re priming dheim, you need to keep pushing down on the primer until you see bubbles coming out of the outputs and inputs. Turn it on then and that should solve the problem It sounds like you didn’t get all of the air out before turning it on. I just read that you said the top was hot Hopefully there wasn’t too much air in there and having it run for an hour might be burning the profesionaal up. Maybe someone else can chime in Last edited by FLGirl; at Renee’ Today I’m feeling: Eheim pro II problems The approach explained in the following thread worked eueim me http: Eheim pro II problems Agreed, too much air in the canister, sounds like.
Eheim Professional II Canister Filters – Product Reviews at The Age of Aquariums – Tropical Fish
You can actually open the canister and fill it manually or siphon from the input tube from the tank into the canister to fill it. Then fill the output tube. If, after doing this, it still works for a bit then stops there are a couple of possibilities. First, the unit is not sealed completely and rather than dripping, it’s sucking in air. After the unit stops pushin water back into the tank, this should be evident by leakage or by there being air in the canister.
Note that air should not enter a correctly sealed system, turning the unit off should result only in siphon and back siphon to the canister. Now, “sealing” may not only be the canister.
Some of the hardware “elbows” that come with some Eheim models have fill caps. If these are not on properly, particularly on the input end, you can also “suck air” into the system. And, obviously, airstone below intakes are a bad idea.
It’s possible the unit is faulty, of course, but most of the time when I’ve seen this having taken in my share of “broken” filters it is because the canister is overfilled. It should not happen, I guess, but if the canister is overfilled with media to the point where the baskets do not slip nicely and to their full depth on top of one another, physical pressure is place on the intake portion of the motor and, for whatever reason, it stops working properly and does what you describe.
Eheim pro II problems wow thanks for profwsional the help, so profesionql morning i just emptied and refilled everything manually.
EHEIM Professional II Pro 2 Aquarium Canister Filter 2028 38 1-owner
It was working for mins before work and when I left it was going strong. Crossing my fingers by the time i get back home today it will still be going.
Thanks for the help, if this works who really knows what was the problem since i have manually refilled it once before and let it “self” prime once as well. Oh well, thanks again. Eheim pro II problems Glad problem is solved. My final suggestion was going to be if the hoses were around the wrong way. The motor got hot too, because it was running dry. Eueim you get more used to them, priming becomes easier too. Thanks for the help guys. Home and Living You Talking to Me? All times are GMT The time now is All rights reserved and copyrightedSimplydiscus LLC.