View and Download Polaris RZR service manual online. RZR Offroad Vehicle pdf manual download. Also for: ranger rzr, Rzr View and Download Polaris RZR owner’s manual online. RZR Offroad Offroad Vehicle Polaris RANGER RZR Service Manual. (20 pages). Service manual on CD for Polaris RZR XP Turbo () UTV models. Polaris RZR EFI Ranger Service Repair Manual, Razor CD. $

Author: Faujora Zolozahn
Country: Zimbabwe
Language: English (Spanish)
Genre: Politics
Published (Last): 12 February 2013
Pages: 207
PDF File Size: 13.13 Mb
ePub File Size: 9.2 Mb
ISBN: 690-5-40952-694-8
Downloads: 1281
Price: Free* [*Free Regsitration Required]
Uploader: Kajimi

The model and VIN numbers are also located on a sticker under the hood B. Special tools may be required while servicing this vehicle. Some of the tools listed or depicted are mandatory, while other tools maybe substituted with a similar tool, if available. Polaris recommends the use of Polaris Special Tools when servicing any Polaris There are exceptions in ownees steering, suspension, and engine areas.

Always consult the exploded views or each manual section for torque values of fasteners before using standard torque. Distance between center of crankshaft and center of driven clutch shaft. Distance between chain link pins Manul.

Owner’s Manuals

Polaris measures chain length in number of pitches. See information provided above. Inspection may reveal rz need for replacement parts. Always use genuine Polaris parts. Engine Oil Change 25 H Perform a break-in oil change at one mqnual Break-In Period Perform these procedures more often for vehicles subjected to severe use.

Clean out Inspect periodically; adjust when parts are Toe Adjustment replaced Polarks Aim Adjust as needed Perform these procedures more often for vehicles subjected to severe use. Each item can be purchased separately at your local Polaris dealer.

Make sure line is not kinked or pinched. Replace fuel line every two years. If the throttle pedal has excessive play due to cable stretch or cable misadjustment, it will cause a delay in throttle speed.

Polaris Ranger RZR Side by Side Service Manual: Manufacturer: : Books

Also, the throttle may not open fully. Installation Inspect the main air filter element and replace if necessary.

Clean the air box thoroughly. Do not clean the main filter, the filter should be replaced. Install a new or clean pre-filter over the main air filter NOTE: If the filter has been soaked with fuel or oil it element. To check the oil level follow the procedure listed below. Remove dipstick and fill sump with 2 quarts 1. Crankcase Drain Plug Torque: Drain plug is accessed through the skid plate.

Low engine compression is rarely a factor in running condition The engine is equipped with a breather hose. Inspect the problems above idle speed. The hose is form fit- A cylinder leakdown test is the best indication of engine ted for a proper fit. The fill plug is located on the side of the gearcase just below the shift lever bell crank.

  CARDIOPATIAS CONGENITAS CIANOGENAS PDF

Maintain the fluid level even with the bottom of the fill plug hole. Position vehicle on a level surface.

Remove the fill plug. The front gearcase lubricant level should be checked and Manua the fill plug and check the fluid level. Add the recommended fluid as needed. The drain plug is located on the bottom right side of the rear Rear Gearcase Specifications gearcase.

Remove recovery bottle cap and polsris coolant using a funnel. Refer to Chapter 3 for cooling system pressure test procedure. Remove any obstructions with compressed air or low pressure water. Wheel, Hub, and Spindle Torque Table Remove the upper engine outlet hose and recovery hose from the top of the radiator.

Operating a RANGER with worn tires will increase the possibility of the vehicle skidding If hub nut was removed, install a new cotter pin after the easily with possible owwners of control. Battery Maintenance Keep battery terminals and connections free of corrosion. If Battery cleaning is necessary, remove the corrosion with a stiff wire brush. Wash with a solution of osners tablespoon baking soda and one rz water.

Battery charge can be maintained by using a A hot exhaust system and engine can cause serious Polaris battery tender charger or by charging about burns. Allow engine to cool or wear protective once a month to make up for normal self-discharge. Install spark plug and torque to specification. Due to the critical nature of the procedures outlined in Recommended Spark Plug: Set steering wheel in a straight ahead position and secure the steering wheel in this position. If toe alignment is incorrect, measure the distance between vehicle center and each wheel.

This will tell pklaris which tie rod Stop the engine. Raise and safely support the front or rear of the vehicle off NOTE: Be sure steering wheel is straight ahead the ground to allow the suspension to fully extend. Brake Fluid Inspection Inspect the brake pad wear surface for excessive wear.

Ownes check the brake pedal travel and inspect the brake fluid reservoir level before each operation. Using tap water in the cooling system will lead to a buildup of deposits which may restrict coolant flow and reduce heat dissipation, resulting in possible engine damage.

Park machine on a level surface. Place the vehicle in of air. Place the vehicle in neutral and set the parking brake. Block the rear wheels. Capacity manuzl Approximately 2 U. Beginning in the crankcase sump, the oil is drawn through an oil galley to the feed side of the oil pump. The oil is mnaual pumped through the oil filter. If the oil filter is obstructed, a bypass valve contained in the filter allows oil to bypass the filter element.

  GRAAL CHRISTIAN DE MONTELLA PDF

Engine Removal Remove the 2 push rivets from the rear of the center console. Because polarid its design configuration, Polaris recommends removing the engine, transmission, and rear gearcase as one assembly. Use the following procedure when engine removal is required. Elevate the rear of the vehicle gzr the ground using a Remove the 6 fasteners retaining the upper bolt-in frame suitable ATV lift and remove both rear wheels.

Loosen the hose clamp between the throttle body and intake Remove the airbox and throttle body from the vehicle as an adaptor.

Take care in not allowing the throttle cable to bend excessively or kink. Carefully place the assembly on the floor next to the vehicle.

Mark the upper jam nut and loosen the lower jam nut. Disconnect the transmission speed sensor harness. If the upper jam nut is moved, shift cable adjustment will Remove the through-bolt that attaches the upper A-arm to Disconnect the engine coolant temperature ECT sensor the rear hub on both sides of the vehicle.

Pivot the A-arms upward and rear hub carriers downward Remove RH engine mount fastener. Remove LH transmission mount fastener. Remove propshaft from the transmission output shaft. Remove only the 4 outer fasteners retaining the engine to the transmission bracket. Then move assembly towards the front of the vehicle while lifting it out to allow the rear gearcase to clear the rear portion of the frame. Remove the valve cover.

RZR Manual | eBay

Mark or tag rocker arms in order of disassembly to keep them in order for reassembly. The cargo box assembly and the upper frame bolt-in brace must be removed to allow enough clearance to remove all the cylinder head rzt.

The following procedure is only for servicing Thoroughly clean cylinder head surface to remove all traces of gasket material and carbon.

Carefully remove the cylinder components. It is recommended to replace seals whenever the cylinder head is mqnual. Hardened, cracked or worn valve seals will cause po,aris oil consumption and carbon buildup. Mark the valves with a white pen. Check valve face for runout, pitting, and burnt spots. Combustion Area Install pilot into valve guide. Valve Seat Reconditioning Apply cutting oil to valve seat and cutter. Place 46 cutter on the pilot and make a light cut.

When using an interference angle, the seat Inspect the cut area of the seat: