ICEA P-45-482 PDF

ICEA P Short Circuit Performance of Metallic Shields and Sheaths on Insulated Cables. standard by Insulated Cable Engineers. ICEA P SHORT CIRCUIT PERFORMANCE. OF. METALLIC SHIELDS AND SHEATHS. ON. INSULATED CABLES. Approval by. AMERICAN. TEST METHOD FOR MEASUREMENT OF HOT CREEP OF POLYMERIC INSULATIONS. ICEA S ICEA S standard for power cables.

Author: Meztizahn Akibar
Country: Colombia
Language: English (Spanish)
Genre: Relationship
Published (Last): 19 January 2013
Pages: 425
PDF File Size: 15.19 Mb
ePub File Size: 12.92 Mb
ISBN: 719-9-27353-955-7
Downloads: 98829
Price: Free* [*Free Regsitration Required]
Uploader: Vit

Open wire lines have a high reactance. While these cables are applicable to the great majority of cable installations that are on grounded systems, they may also be used on other systems for which the application of cables is acceptable, provided the above clearing requirements are met in completely de-energizing the faulted section.

It is accomplished by means of strand and insulation shields.

While resulting in slightly higher reactances than three cables in a non-magnetic duct, it is optimal relative to the alternative of a single cable in a magnetic duct. Where electrostatic discharges are of low iccea intensity not to p-45-4822 cable but are sufficient in magnitude to interfere with radio or television reception. Grips are not suitable for all vertical riser installation and the above is offered as a general guide only.

The tape may be conducting compound, fibrous tape faced or filled with conducting compound, or conducting fibrous tape. Single conductors should not be installed in individual magnetic conduit because of the excessive reactance.

To satisfy my own curiosity, I checked a few text books to see if I could corroborate this. The following equation can be utilized to find the reactance of a given configuration by using the concept of geometric mean radius. Their use is recommended also for resonant grounded systems.

Most Related  EASTERN BODY WESTERN MIND BY ANODEA JUDITH PDF

Various modifications are necessary for use under special conditions is covered in notes on the nomogram. To protect cable connected to overhead lines or otherwise subject to induced potentials. The maximum short-circuit current that can flow in a given shield or sheath for a given time, or 3. Where regulation is an important consideration several factors should be kept in mind in order to obtain the best operating conditions.

For additional security, a mechanical device, such as a clamp, may be used to fasten the ends of the connection together. It is recommended that the shield be grounded at cable terminations and at splices and taps. Three conductors in magnetic conduit will have a somewhat higher reactance than cables in non-magnetic conduit. Download Now Defense manufacturing is all about project manufacturing and project accounting. The capacitance of a one conductor shielded cable is given by the following formula: In some cases, the efficiency of protective equipment may require proper size ground wires as a supplement to shielding.

The effective area of composite shields is the sum of the effective areas of the components. Where the surface of cable collects conducting materials. The resultant intensity of discharge may be sufficient to cause burning of the insulation or jacket.

General Calculations Excerpt from PRYSMIAN`S WIRE AND CABLE

Current Carrying Capacity of Copper Conductors. Definition of shielding Shielding of an electric power cable is the practice of confining the dielectric field of the cable to the insulation of the conductor or conductors. Also, they may be used when additional insulation strength over the percent level category is desirable. Are you an Engineering professional? XLPE jackets promise sustainability benefits including: Where non-shielded non-metallic jacketed cables are used in underground ducts containing several circuits, which must be worked on independently, the external field if sufficiently intense can cause shock to those who handle or contact energized cable.

Most Related  APC BE600N-BR PDF

Defense manufacturing is all about project manufacturing and project accounting.

General Calculations Excerpt from PRYSMIAN`S WIRE AND CABLE

This advantage is obtained only if the shield is grounded. For three-phase circuits, use voltage to neutral and resistance and reactance of each conductor to neutral.

Auxiliary nonmetallic conducting shields may adhere to the insulation, so that the use of a grit aluminum oxide cloth or similar material may be required to assure removal of the conducting material from the insulation surface See pages 28 – 30 for generalized discussion of cable preparation for splicing and terminating.

Register now while it’s still free! Every jcea I found used a different formula which does take the shield diameter into account. Transition from moist to dry earth. Definite rules cannot be established on a practical basis for all cases. P-455-482 the surface of the cable is separated from ground by a thin layer of air and the air gap is subjected to a voltage stress, which exceeds the dielectric p-45-4482 of air, a discharge will occur, causing ozone formation.