HORMANN UAP1 PDF

Find great deals for Hörmann Universaladapterplatine UAP 1. Shop with confidence on eBay!. For Hörmann door, Type: SupraMatic, Rotamatic / P / PL from year 09/ and LineaMatic built from 10/ – About for direction selection (up / stop / close). For inputs to Hormann: does it mean that I have to run 6 wires for this section from Loxone to Hormann? Or is it possible to reuse the wire for

Author: Mezimuro Voodookazahn
Country: Kenya
Language: English (Spanish)
Genre: Politics
Published (Last): 8 April 2008
Pages: 113
PDF File Size: 8.49 Mb
ePub File Size: 12.31 Mb
ISBN: 379-2-19767-672-3
Downloads: 60580
Price: Free* [*Free Regsitration Required]
Uploader: Salabar

Whith that one I can tell when the UAP1 is sending and when it is receiving! To control the door via a home automation system you have several options:.

Therefore I plan to hook up the bus to a network outlet I have in my garage that leads all the way down into my basement where my network rack sits. Currently I send a 0.

Fortunately the page gives you a nice lookup table for the CRC values which I then used in my Python program to verify all the messages I’ve recorded so far. That occured at baud 8N1 so I think that must be the correct baudrate. Speak directly to the motor and get the signals directly onto the homeautomation system.

No common CRC8 generator gave me the same result as the messages have. RS is Half-Duplex, that means that only one participant on the bus can talk at a given time. Intelligent contol panels I found this guidewhich made the setup easier horamnn I’ve setup everything accordingly.

Hörmann Universaladapterplatine UAP 1

Bus scan At startup the Master scans the bus for devices. The description in the patents is not cristal clear at least to me but still extremely helpful in figureing uaap1 whats going on on the bus. I’ll try to extend this artcle or write a followup in the future.

Most Related  DESSINER EN PERSPECTIVE PARRAMON PDF

It decrements this address and scans the entire bus. Connect potential free contacts directly to the motor.

I see one for your supramatic seems a bit over complicated for a Garage Door – however reading the instructions for the ventilation position You might find uap you need here.

The slave responds to a status request by the master. It seems that this must happen when the UAP1 is connected to the motor. Burglar alarm As you can see the only status bit set, is from the second byte and means reversing according to the patent which makes no sense to me.

Broadcast status From the beginning the master sends a broadcast status message. Any help would be greatly appreciated. After having discussed that issue with my Italian friend he was able to figure out the polynom hormsnn as well as the initial value 0xF3 for the CRC algorithm.

Pedestrian door Bit 6: Ken 4, 1 4 When the board is powered while the logic analyzer is collecting data, we see these bytes comming in:.

If the selected height is too low, a 2-digit number starting with 1 will appear with a flashing decimal point see section Hodmann the patent doesn’t say anything about the device codes. Bottom side of the circuit board: I might misinterprete some of them at this point: Hi Ken, as you say in the beginning of the reply the UAP enables me to “open the garage door” and “close the garage door” which is what I want to achieve same as what the person who wrote the guide I linked to achievedsorry if I didn’t explain properly.

Hörmann Universaladapterplatine UAP 1 | Smolka Tor- und Antriebstechnik Berlin Online Shop

Here’s what I got using the USB converter with the door closed idling: In my case the UAP1 answers: Not much to see here, just that all pins of the 6-pin RJ12 sockets are directly conected to each other. That tells me that it appears your UAP will not allow for the individual movements that you kap1 looking to achieve. Usa a UAP1, a small extension box to have better control over the motor and get some feedback signals.

Most Related  ASSASSINS SONDHEIM SCRIPT PDF

Then I encountered another problem I didn’t think about in the first place. The changed partial opening position is saved.

Reverse engeneering the Hörmann UAP1 protocoll

They make me able to export the analyzed data as CSV. The remotes require a 2 second press to avoid accidental presses, have you tried making your pulse longer? Why it doesnt scan the adresses down to ? Option relay on Bit 3: Reverse engeneering the protocoll I expected a rather simple protocoll where no comunication happens until the UAP1 gets triggered by a switch, but I was more than wrong.

low voltage – Hormann garage door opener automation with Loxone – Home Improvement Stack Exchange

As you can see the only status bit set, is from the second byte and means reversing according to the patent which makes no sense to me. To supply the board with 24VDC, which normally comes in via the RJ12 connector, I simply used the terminals taht normally connect the switches. I searched the internet for information about the bus, but little to nothing can be found about it. I’ve set two analyzers for async serial data on both, the RX and the TX line.

To control the door via a home automation system you have several options: Unfortunately no other communication is happening when I trigger a “close door” for example. Could it be that you 0.