FTBL USB FIFO (USB – Parallel) I.C.. The FTBL is the lead free version of the 2nd generation of FTDI’s popular USB FIFO I.C. This device not only adds. FTBL datasheet, FTBL circuit, FTBL data sheet: ETC – FTBL USB FIFO (USB – Parallel) I.C.,alldatasheet, datasheet, Datasheet search site for. FTBL datasheet, FTBL circuit, FTBL data sheet: FTDI – USB FIFO ( USB – Parallel) I.C.,alldatasheet, datasheet, Datasheet search site for Electronic .

Author: Voodootilar Viran
Country: Spain
Language: English (Spanish)
Genre: Automotive
Published (Last): 16 August 2012
Pages: 466
PDF File Size: 11.93 Mb
ePub File Size: 20.43 Mb
ISBN: 850-8-62284-616-3
Downloads: 83457
Price: Free* [*Free Regsitration Required]
Uploader: Mazugul

The following commands will be used in the example:. Support for high power USB Bus powered devices. To send data from the peripheral to the host computer, simply write the byte-wide data into the module when TXE is.

Future Designs FTBL – PDF Datasheet – USB In Stock |

When the host sends data to the peripheral over USB, the device will take RXF low to let the dataheet know that at least one byte of data is available. The next example is with adc read datashset command. Set Top Box S. Area 1 – In this area, the user can add unlimited inputs and outputs, from different data types – analogue, digital, integer, string, datetime. Mode – this parameter is very important, because some of the FTDI devices work well in different modes.

FT245BL Datasheet PDF

InvertOuts – the digital outputs of the device are presented as block’s inputs. The block will parse it and to set the parsed value to block’s output ADC0.

Datashewt notes, software and development modules for this application area will be available from FTDI and other 3 developers.

New Bit-Bang Mode allows the data bus to be used. This device not only. See the seperate datasheet for package dimensions. In this mode, any residual. The value of block’s input RelayIndex is represented with text 0 or 1; So at Send data area we will describe the Send text composition as: The parameter opens the following interface:. To send data from the peripheral to the host computer, simply write the byte-wide data into the module when TXE is low. We can add a sequence of characters to be added at the end of each ft45bl text, the same symbols will be expected to be contained as the end of the received text response from the device.


Commands to set the baud rate are ignored – the device always transfers data at its fastest rate regardless of the.

FT245BL USB FIFO IC (Lead Free Package) Data Sheet

The received text from the device contains two lines, each of them ends with CR. The following commands will be used in the example: The main interface of the parameter Settings consists of three areas: The communication parameters of the block are: If the parameter is unchecked, the communication speed can be increased up to commands to device per second.

This circuit is now embedded fatasheet — the pin assigned to this function is now designated as the TEST pin and should be tied to GND for normal operation. Figure 10 Self Powered Circuit with 3.

The peripheral can read a data byte every time RXF goes low. If the hardware after FTDI chip inverts the digital outputs, then it is more easy to invert all the signals, which enter ft245hl the block than to use NOT digital block to invert every input signal.

FTBL Datasheet(PDF) – Future Technology Devices International Ltd.

The user has to select one of available FTDI devices. The chip has 8 IO pins, which can be set as digital input ot output, but works well with Synchronous mode, in case we use Asynchronous mode, the device will work too, but every reading of digital inputs will be slowly, because TimeOut of 1 sec will appear. The received text response is two-line and each line ends with the CR too. Is case the device USB cable is very long, cable is disconnected or for other reason, some of the commands between computer and device can be not processed from device, then the described output will become to high value for 3 sec.


If this parameter is 0, the commands will be send per every DiscreteTime interval described in block Process. In-built support for event characters.

We have to use the commands: The FTBQ is also a lead free package. RXF goes high after every byte read. Example pelase, load SerialUni. The parameter opens the following interface: Web Site for the contact details our distributor s in your country.

Part number for this version is FTBQ. When the input GetVersionSendCommand becomes to high level, the command will be send to the device.

The settings of every command are: If the corresponding input of the command is connected, the command will be send only when the input becomes at high level; Wait between commands[ms] – if the commands are too frequent, the time between two commands will be no less than this parameter; Example: The device works well in Asynchronous mode, so ddatasheet set the parameter Mode of the block to Asynchronous. The sent text is a composition of the dataasheet of the blocks’ inputs.

All other trademarks are the property of their respective owners. USB Bulk or Isochronous data transfer modes. The received text response from the device is analyzed by the block and the corresponding outputs of the block are set according to the values in the received text response.

The interface of the command is shown below: In this case if Disable parameter is checked, the process will be started without the device. For further details, consult the device pin-out description and functional descriptions.