EUROMAP 70 Electrical Interface between Injection Moulding Views. 6 years ago. Euromap, · Electrical, · Interface, · Injection, · Moulding. Euromap 2: Mould Fixing Dimension for Injection Moulding Machines. Specific information .. Mechanical properties, , Mechanical restraints, The electric control M2C is used for large machines. – highest safety standards ( as per EN /EN ) – standardised integration via EUROMAP 70 interface.

Author: Vigore Gugami
Country: Trinidad & Tobago
Language: English (Spanish)
Genre: Medical
Published (Last): 22 April 2008
Pages: 113
PDF File Size: 3.29 Mb
ePub File Size: 1.89 Mb
ISBN: 953-7-97014-806-9
Downloads: 94773
Price: Free* [*Free Regsitration Required]
Uploader: Shakabar

Figure 7 Magnetic clamping system in a rubber moulding press of the company PanStone Plate size xmm, magnetic force kN realised for small and medium mould weights. All signals are continuous signals unless otherwise noted. Power is only required for about 2 seconds to magnetise clamp the system at the beginning. The magnetic force is generated in a very flat, highly concentrated magnetic field. Figure 11 Magnetic clamping systems for an injection moulding machine of the company Krauss Maffei Closure force: Magnetic clamping plates for different sectors of industry as e.

Plug on the injection moulding machine male.

The mould halves are heated by the magnetic heating plate. This is intended to provide interchangeability.

Technical Recommendations | EUROMAP – European Plastics and Rubber Machinery

The interface to the press is always designed redundantly, is effected via potential-free contacts to stop or drive the machine. Quick die change on presses and automatic punching machines. The magnetic clamping systems or clamping plates have been especially designed for injection moulding machines, rubber presses, die casting euroap, mould carrier and presses for metal forming.


Also very small moulds are safely clamped. Inquiry – checklist for a quotation: All of the desired performance levels can be met. The technology of the magnetic clamping plates is based on the principle of an electro-permanent magnet and is thus safe, even in case of a pressure failure.

Size and geometric shape can be freely designed as requested by the customer. The design of the magnetic plates is very flexible and can be adapted in size and shape for different requirements according to the user’s specification. Figure 10 Magnetic clamping system installed in Arburg Eiromap High concentration effect of the magnetic force close to the centring ring.

EUROMAP 70 – version

The eurompa supply of the MCS is also specified. A further supplier added v. There are no limits set to the geometric shape of the magnetic plates.

In operation, the system works independently of any power supply. For easy eufomap safe mould change, roller bars with spring packs are installed below the magnetic plate.

Plug on the injection moulding machine female. A supplied separate control in combination with the press control provides the required safety for man and machine.

The electric control M1C is used for small and medium-sized machines. This penetrates only a few millimetres into the die base plate and will therefore have no impact on the die and the products. Pin a2 and Table 2: The electric control M2C is used for large machines. ejromap


EUROMAP 70 – version 1.5

Clamping and unclamping of several dies at the same time within a second. Pin d2 18 — 36V DC max. Figure 8 Magnet clamping system for an injection moulding machine of the company Engel Closure force: Clamping forces of e. Figure 13 Magnetic clamping systems for an injection moulding machine of the company Krauss Maffei Closure force: The signals are conducted from the signal source to the respective pin.

The forces can be adapted upwards and downwards to the needs of the machine.

Figure 6 Magnetic clamping system in a rubber moulding press of the company Wickert Plate size xmm, magnetic force eurojap to kN possible. The system itself does not have any movable elements and euroomap practically maintenance-free.

Products Service Support Downloads Company. In addition, all requirements of EN for injection moulding machines and EN for presses are met. Safety of the magnetic clamping system: It is suitable for fitting or retrofitting without any problems in nearly all presses. The fixation is made in an all around clamping groove by means of clamping claws.