EUP 8054 PDF

EUP datasheet, EUP circuit, EUP data sheet: EUTECH – Standalone Linear Li-Ion Battery Charger With Thermal Regulation in ThinSOT. EUP Price, EUP Stock, Buy EUP from electronic components distributors. Instant result for EUP Buy Eutech Microelectronics EUP at Win Source. Source EUP Price, Find EUP Datasheet,Check EUP In stock & RFQ from online electronic .

Author: Yozshujind Goltirn
Country: Ukraine
Language: English (Spanish)
Genre: Video
Published (Last): 22 May 2012
Pages: 188
PDF File Size: 6.94 Mb
ePub File Size: 8.51 Mb
ISBN: 690-1-70712-702-9
Downloads: 23718
Price: Free* [*Free Regsitration Required]
Uploader: Gurg

If this voltage drops below the 4. Positive Input Supply Voltage.

EUP,EUP pdf中文资料,EUP引脚图,EUP电路-Datasheet-电子工程世界

When it reaches the 1. A charge cycle restarts when the battery voltage falls below 4. No series resistor is needed if tantalum capacitors are used. State Diagram of a Typical Charge Cycle An internal undervoltage lockout circuit monitors the wup voltage and keeps the charger in shutdown mode until VCC rises above the undervoltage lockout threshold.

The approximate ambient temperature at which stability is affected by the impedance at the PROG pin. The EUPX does not include this trickle charge feature. Driving this pin to voltages beyond the clamp voltage will draw currents as high as1.

Figure 10 shows that by using two different value pull-up resistors, a microprocessor can detect all three states from this pin. Therefore, an N-channel has ended. The charge voltage is fixed at 4.

Provides power to the charger. This ensures that ekp battery is kept at or near a fully charged condition and eliminates the need for periodic charge cycle initiations.


VCC can range from 4. Provides charge current to the battery and regulates the final float voltage to 4.

Figure 12 shows an example of how to indicates that a charge cycle is in progress. Other heat sources on the board, not related to the chargermust also be considered when designing a PC board layout because they will affect overall temperature rise and the maximum charge current. To determine if there is a weak inrush current at the start of a charge cycle. The charge current can be set according to typical not worst-case ambient temperature with the assurance that the charger will automatically reduce the current in worst-case conditions.

In all modes, the voltage on this pin can be used to measure the charge current using the following formula: An internal precision resistor divider from this pin sets the float voltage which is disconnected in shutdown mode.

Pulison IC chips EUP8054 EUTECH SOT23-5 single section lithium battery management IC brand new

Open-Drain Charge Status Output. When charging in constant-current mode, this pin servos to 1V. Feedthrough vias to inner or backside copper layers are also useful in improving the overall thermal performance of the charger. Once the average charge current drops below BAT pin is less than 2. Block Diagram DS Ver1. CHRG output enters a strong pull-down state during recharge cycles.


The footprint copper pads should be as wide as possible and expand out to larger copper areas to spread and dissipate the heat to the surrounding ambient.

Standalone Linear Li-Ion Battery Charger With Thermal Regulation In ThinSOT

Nearly all connected to the charger output. The thermal path eu; the heat generated by the IC is from the die to the copper lead frame, through the package leads, especially the ground lead to the PC board copper. A new charge cycle can be initiated by reconnecting the program resistor.

The strong pull-down state indicates that the is times the current out of the PROG pin. This parameter is not 80544 to the EUPX. Absolute Maximum Ratings are those values beyond which the life of the device may be impaired.

EUP lithium-ion charger circuit diagram

This feature protects the EUP from excessive temperature and allows the user to push the limits of the power handling capability of a given circuit board without risk of damaging the EUP The PC board copper 80554 the heat sink. The the average battery current as shown in Figure 8. The EUP are guaranteed to meet performance specifications from 0 to This pin is also clamped to approximately 2.