ATTANSIC ATTP1 PDF

, 13, ATTANSIC, -. Kring Electronics Co., Ltd. , -, Attansic, sop8. 63, 0, ATTANSIC, -. Rantle East Electronic. , -, ATTANSIC, SOP. 年12月11日 ATTP1_ – Technology Corporation ATTP1 Over Temperature Please contact Attansic Technology Corp. for the latest documents. Attansic. ATTP1. Tel:. MFG:. ATTANSIC. Picture. D/C:. 09+. QTY:. Packaging:. SOP8L. Package:. Note:. 原装正品. Support. No“ATTP1”Picture.

Author: Voodoorg Dagar
Country: Cayman Islands
Language: English (Spanish)
Genre: Automotive
Published (Last): 25 June 2012
Pages: 371
PDF File Size: 2.96 Mb
ePub File Size: 5.84 Mb
ISBN: 809-2-23841-625-7
Downloads: 85068
Price: Free* [*Free Regsitration Required]
Uploader: Makazahn

If you muck this up and turn your board into a doorstop, don’t come crying to me.

ATTP1 Stock|ATTP1 PDF|ATTANSIC Agents

Our members offer you their FAQs! Apply a dollop of gel type super glue or some other fastening agent to each of your jumpers to near pin 97 and pin to keep them from flexing too much and breaking the pins off the chip.

Find pin of the Winbond chip. It didn’t change my temp readings at all, but it is theoretically possible for there to be a slight change in the reading. I’ve personally verified this a few times myself, so I know it works.

If you have previously modded your mobo to read the thermal diode, you MAY find that your temps are degrees higher than they used to be. Soldering on these quad flat packs is a real PITA! BB code is On.

ATTP1_1.3.pdf

Also make sure that you don’t accidentally bridge any of the adjacent pins with solder while you are trying to lift this pin. Webb City, Mo Posts: It is the pin at the very top left corner of the Winbond chip on the top, when viewed as described above. Solder aytp1 pin 61 first, then pin As a result, when you tie the Temp 3 input to the thermal diode while the Attansic chip is hooked up, it causes the Attansic chip to think that the CPU has exceeded safe temp limits.

Most Related  HIPERBARIK OKSIJEN TEDAVISI PDF

You’ll find that trying to solder the wires to the broken pins, while not impossible, is exceedingly difficult. I didn’t think it did.

NF7-S CPU Thermal Diode Mod, Version – AOA Forums

Well, I’ve solved that problem. A fine tip soldering iron is definitely a must. While this mod works pretty well, it has one glaring drawback, which I mentioned in the previous post: Where’s the thermal diode? Add Thread to del.

That’s all there is to it. I’ve been looking for developer’s docs for the NF2 chipset and haven’t been able to find any. Run a jumper from pin 61 of the Winbond chip to pin This connects to channel two of the Winbond chip, which means you can now use channel two on pin for something else. I find that the edge of a single-edge razor blade works rather well for helping lift this pin while I apply heat with the soldering iron.

You don’t need to move the jumper though. I just have you solder directly to the pin because it is simpler to explain. However, be aware that soldering pin 97 and pin back down is rather tricky because of the fine spacing of the pins. I’ve got pretty steady hands and it took me three tries to get the jumper soldered correctly without bridging solder to the other pins.

Most Related  CODAP 2005 DIVISION 2 PDF

It’s already in the right place.

ATTP1 Attansic CPU thermal protection controller chip SOP8

Also note that, because you are now monitoring the thermal diode directly, the thermistor in the socket is now rather pointless. As for the other, yes you should solder pin 4 of the Attansic back down to the mobo. However, because of the way the mod is done, the odds of messing it up in such a way that you dissable the OTP function are pretty low. Make sure you leave just a dollop of solder on the end of the jumper wire when you tin it or you’ll never get it to solder properly but don’t leave too much, or you’ll bridge the pins.

Check out our sister site! This is the analog voltage input. This means that your poor CPU is going to blow its brains out just as soon as it loses proper cooling for any reason. The wire will need to be about 8 cm 3″ long.