ASTM Standards::} 70 Test Methods and Definitions for Mechanical Testing of Steel Products. 3. Terminology. Definitions—For definitions of terms used. Chemical and mechanical properties of ASTM A duplex and super-duplex pipe materials. What is duplex steel, use cases, corrosion resistance vs. SS. ASTM A/AM: Standard Specification for Seamless and Welded Ferritic/ Austenitic Stainless Steel Pipe.
|Published (Last):||16 September 2016|
|PDF File Size:||11.67 Mb|
|ePub File Size:||8.16 Mb|
|Price:||Free* [*Free Regsitration Required]|
Duplex Steel Products: But all pipe tested since the last acceptable standardization must be retested for acceptance.
Single-seam, atm or double- welded austenitic pipe for high temperature and general corrosive applications. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.
The pipe may be accepted based on visual examination, provided the imperfection is less than 0. This requirement does not preclude additional testing at earlier stages in the processing. Notches shall be placed on both the OD and ID surfaces. Combining values from the two systems may result in nonconformance with the specication.
Transverse Tension Tests S2.
The inch-pound units shall apply unless the M designation of this specification is specified in the order. A steel pipes piping.
ASTM A Seamless Pipe, ASTM A Welded Pipe, ASTM AM Duplex Pipes.
Pipe having other dimensions may be furnished provided such pipe complies with all other requirements of this specification. The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets.
Originally approved in If this supplementary requirement is specied, the number of tests per pipe required shall also be specied. Tension tests, hardening tests, flattening tests, hydrostatic tests and nondestructive electric tests shall be made to conform to the specified requirements. Increasing temperatures also increase the susceptibility of stainless steels to stress corrosion cracking.
High quality exotic piping products from approved manufacturers: The hole diameter shall vary with NPS as follows: Referenced Documents purchase separately The documents awtm below are referenced within the subject standard but are not provided as part of the standard. Duplex Steel Tubing Supplied to.
The Class Number dictates how the pipe is welded and what non-destructive tests:. The dimensions of these standards should not be construed as the minimum size imperfection detectable by such equipment.
– Buy and Sell Project Materials
ASTM A790 Standard for Duplex Stainless Steel Pipe
The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Duplex Stainless Steels Products Manufacturers. If a qstm from any length shows objectionable defects, the length shall be rejected, subject to removal of the defective end and subsequent retests indicating the remainder of the length to be sound and reasonably uniform material.
It should be recognized that different techniques should be employed to detect differently oriented imperfections. No radiography is required. The dimensionless designator Nominal Pipe Size nominal pipe size has been substituted in this standard for such traditional terms as nominal diameter, size, and nominal size. The high chromium, molybdenum and nitrogen contents of provide corrosion resistance superior to common stainless steels, such as, L and L in most environments and Citizen Metals has been actively involved in ensuring the best quality of the same to our clients.
Active view current version of standard.
These steels are susceptible to embrittlement if used for prolonged periods at elevated temperatures. Pipe having other dimensions may be furnished provided such pipe complies with all other requirements of this specification.
The values stated in each system are not exact equivalents; therefore, each asrm must be used independently of the other. We at Ganpat Industrial Corporation ensure that all our materials go through strict quality tests before dispatching them to our clients. 7a90 X1 of this specification lists the dimensions of welded and stainless steel seamless pipe as shown in ANSI B Short lengths are acceptable and the number and minimum length shall be agreed upon between the manufacturer and the purchaser.
Optional supplementary a970 are provided for pipe when a greater degree of testing is desired. One hole shall be drilled in the weld, if visible.