SPIRALCO is a company specialized in the production of spiral-weld steel tubes and pipes. May 23, 1 This speciﬁcation speciﬁcation is under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel and Related Alloys Stainless Alloys. ASTM A Standard Specification for Pipe, Steel, Electric-Fusion (Arc)-Welded ( Sizes NPS 16 and Over) Reprinted from the Annual Book of ASTM Standards.
|Published (Last):||4 March 2008|
|PDF File Size:||5.1 Mb|
|ePub File Size:||20.86 Mb|
|Price:||Free* [*Free Regsitration Required]|
ASTM A / ASME SA / Pipe Steel Electric Fusion (ARC) Welded – Aesteiron Steel Pipes
It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. For additional details and information, please refer to these specifications. This standard does not purport to address all of the safety concerns, if any, associated with its use. Finished pipe shall be commercially straight. All burrs at the ends of pipe shall be removed.
Yield strength, min Ksi Mpa. It is the re respo sponsi satm bility ity of the use userr of thi thiss sta standa ndard rd to est establ ablish ish appro app ropri priate ate saf safety ety and hea health lth pra practi ctices ces and awtm determ ermine ine the applicability of regulatory limitations prior to use. This standard does not purport to address all of the safety concerns, if any, associated with its use. Pipe shall be furnished with a plain right angle cut or with bevel ends as specified.
Tensile Properties of Production Welds All repaired pipe shall be tested hydrostatically. Defects in the welds, such axtm sweats or leaks, shall be repaired or the piece rejected at the option of the manufacturer. Note 4—The dimensionless designator NPS nominal pipe size has been substituted in this standard for such traditional terms as “nominal diameter”, “size”, and “nominal size”.
The materials for these pipes as well as the welding procedure shall conform to other ASTM standards listed herein. Get in Touch with us Superior Steel Overseas. One weld test for the reduced-section tension shall be made from each lot of ft.
Developed using supreme quality raw material, all our products are known for their durability, resistance against aetm, fine finishing and anti-abrasive nature. Year of Establishment Link to Active This link will always route to the current Active version of the standard.
C List of world top ten steel producing nations during Nov View Contact Call Seller Now. Active view current version of standard. Within the text, the SI units are shown in brackets.
Historical Version s – view previous versions of standard. Closer tolerances may be established by agreement between the manufacturer and the purchaser. We need your help! Note 2—For testing methods not specifically covered in this specification, reference can be made to Asfm Methods and Definitions Awith particular reference to Annex A 2 on Steel Tubular Products.
The wall thickness and weight for welded pipe under this specification shall be governed by the requirements of the specifications to which the steel was ordered. Atsm is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
When specific straightness requirements are desired, the order should so state, and the tolerances shall be a matter asttm agreement between the manufacturer and the purchaser. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM A134 and ASME SA134 Carbon Steel Pipes
Test pressure shall be held for not less than 5 sec, or for a longer time as zstm upon between the purchaser and the manufacturer. Work Item s – proposed revisions of this standard. Note 1—Acceptability for many services may be controlled by codes or standards such as those published by the American National Standards Institute and American Society of Mechanical Engineers.
ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, axtm or up to date.
The weld-test specimens for the reduced-section tension test shall be taken perpendicularly across the weld and the test pieces shall have the weld in the middle of the specimen.